Benq MP510 Uživatelský manuál

WelcomeMP510 Digital ProjectorMainstream SeriesUser Manual

Introduction10Controls and functionsProjector1. Focus ring (See "Fine-tuning the picture clarity" on page 26 for details.)Adjusts the focus

Introduction 11Remote control1. Power (See "Start up" on page 21 and "Shutting down the projector" on page 32 for details.)Turns t

Introduction12Remote control effective rangeInfra-Red (IR) remote control sensors are located on the front and the back of the projector. The remote c

Positioning your projector 133. Positioning your projectorChoosing a locationYour projector is designed to be installed in one of four possible instal

Positioning your projector14Obtaining a preferred projected picture sizeThe distance from the projector lens to the screen, and the video format each

Positioning your projector 15horizontal distance from the center of the screen (projection distance), and the vertical offset height of the projector

Positioning your projector16Projection dimensionsRefer to "Dimensions" on page 48 for the center of lens dimensions of this projector before

Connection 174. ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use

Connection18Connecting Video source devicesYou can connect your projector to various Video source devices that provide any one of the following output

Connection 19Connecting a Component Video source deviceExamine your Video source device to determine if it has a set of unused Component Video output

Table of contents2Table of contentsImportant safety instructions ... 4Introduction ...

Connection20Connecting an S-Video or a composite Video source deviceExamine your Video source device to determine if it has an unused S-Video or compo

Operation 215. OperationStart up1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check

Operation22If a PC input is selected and the resolution is not 800 x 600, you will see a Resolution Reminder as below. For a better picture quality, p

Operation 23iii. Press Down to cancel the password set-up and return to the OSD menu.To disable password protection, go to the Setting > Password

Operation24Switching input signalThe projector can be connected to multiple devices at the same time. However, it can only display one at a time. To c

Operation 25To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjust

Operation26Fine-tuning the picture clarityIf needed, sharpen the picture by rotating the focus ring.If you are still not satisfied with the picture cl

Operation 27Optimizing the pictureSelecting a picture modeThe projector is preset with several predefined picture modes so that you can choose one to

Operation28Video input sourcesVideo input sources are video (movie) based signal timings connected using the video cables Component Video (YPbPr), S-V

Operation 29Adjusting ContrastThe higher the value, the greater the contrast. Adjust this control so that white areas of the picture appear bright and

Table of contents 3Timing chart ... 49Warranty and Copyright information ...

Operation304. Press Down to highlight Timer Position and set the timer position by pressing Left/ Right.Upper left J lower left J upper right J lowe

Operation 31Freezing the picturePress on the remote control to freeze the picture. An icon will display in the lower right corner of the screen. T

Operation32Shutting down the projector1. Press Power and a prompt message appears. Press Power a second time to turn the projector off.2. The Power i

Operation 33Menu operationMenu systemPlease note that the on-screen display (OSD) menus vary according to the signal type selected.*When a Video or S-

Operation34Using the OSD menusThe projector is equipped with on-screen display (OSD) menus for making various adjustments and settings.There are 17 di

Operation 35Picture menuSome picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on th

Operation36Pro-Picture menuSome picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on

Operation 37Setting menu FUNCTION(default setting / value)DESCRIPTIONOSD Time(20)Sets the length of time the OSD will remain active after your last bu

Operation38Advanced menuFUNCTION(default setting / value)DESCRIPTION(default setting / value)Mirror()The projector can be installed on a ceiling or be

Operation 39Information menuThis menu shows you the current operating status of the projector.Some picture adjustments are available only when certain

Important safety instructions41. Important safety instructionsYour BenQ projector is designed and tested to meet the latest standards for safety of in

Maintenance406. MaintenanceCare of the projectorYour projector needs little maintenance. The only thing you need to do on a regular basis is to keep t

Maintenance 41Lamp informationCalculation of lamp hourWhen the projector is in operation, the duration (in hours) of lamp usage is automatically calcu

Maintenance42Replacing the lamp• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing t

Maintenance 435. Disconnect the lamp connector by pushing it against the projector while pulling it up.6. Loosen the screw that secures the lamp.7. Li

Maintenance4414. Restart the projector.Do not turn the power on with the lamp cover removed. 15. Resetting the lamp counter Do not reset if the lamp i

Maintenance 45IndicatorsIllustration• Blank -: Light OFF•O: Orange light•: Light flashing• R: Red light•: Light ON• G: Green lightLight Status & D

Maintenance46Light Status & DescriptionPower Temp LampThermal events--The projector has shutdown automatically. If you try to re-start the project

Troubleshooting 477. TroubleshootingThe projector does not turn on.No pictureBlurred pictureRemote control does not workThe password is incorrectCause

Specifications488. SpecificationsProjector specifications All specifications are subject to change without notice. GeneralProduct name Digital Project

Specifications 49Timing chartSupported timing for PC inputSupported timing for Component-YPbPr inputSupported timing for Video and S-Video inputsResol

Important safety instructions 5 Safety Instructions (Continued)7. The lamp becomes extremely hot during operation. Allow the projector to cool for ap

Warranty and Copyright information509. Warranty and Copyright informationLimited warrantyBenQ warrants this product against any defects in material an

Regulation statements 5110. Regulation statementsFCC statementCLASS B: This equipment generates, uses and can radiate radio frequency energy and, if n

Important safety instructions6 Safety Instructions (Continued)12. Do not place this projector in any of the following environments. - Space that

Important safety instructions 7Safety instructions for ceiling mounting of the projectorWe want you to have a pleasant experience using your BenQ proj

Introduction82. IntroductionProjector featuresThe projector integrates high-performance optical engine projection and a user-friendly design to delive

Introduction 9Projector exterior viewFront/upper sideRear sideSee "Connection" on page 17 for details.Under side1. External control panel (S