BenQ PB6240 Uživatelský manuál

WelcomePB6240 Digital ProjectorPortable SeriesUser’s Manual

Introduction6Shipping contentsThe projector is shipped with the cables required for connection to a PC and to video equipment. Carefully unpack and ve

Introduction 7Optional accessoriesProjector exterior viewFront / upper sideRear side1. Macintosh adapter2. 250W lamp module3. Ceiling mount kit4. Wire

Introduction8Bottom sideConnector panelRefer to page 12 for more information on making connections to various equipment.Lamp coverFront adjuster footR

Introduction 9Controls and functionsExternal control panel131210911534872161. Power (Refer to pages 17 and 22 for more information.)Turns the projecto

Introduction10Remote Ccontrol1. Power (Refer to pages 17 and 22 for more information.)Turns the projector on or off. 2. FreezeThe image is frozen when

Introduction 11Remote control effective rangeInfra Red (IR) remote control sensors are located on the front and the back of the projector. The remote

Positioning your projector12Positioning your projectorChoosing a locationYour projector is designed to be installed in one of four possible installati

Positioning your projector 13Obtaining a preferred projected image sizeThe distance from the projector lens to the screen, the zoom setting, and the v

Positioning your projector14• The recommended focus range is from 1.5 ~ 8 meters (6 ~ 32 feet).• There is 3% ~ 5% tolerance among these numbers due to

Connection 15ConnectionWhen connecting a signal source to the projector, be sure to:1. Turn all equipment off before making any connections.2. Use the

CopyrightCopyright 2005 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a

Connection16The following standards are supported in the digital TV function:Connecting Video or S-Video devices If the selected video image is not di

Operation 17OperationStart up1. Switch all of the connected equipment on.2. Plug the power cord into the projector and into a wall socket. Turn on the

Operation182. When the function is activated for the first time, a prompt will display on the screen. Use the 5 or 6 button to select a number for eac

Operation 19Adjusting the imageAdjusting the heightThe projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These adjust

Operation20Correcting keystoneKeystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs

Operation 21Switiching input signalThe projector can be connected to multiple devices at the same time. To sequentially select input sources, press th

Operation22Shutdown1. Press Power and a warning message appears. Press Power a second time to turn the projector off. 2. The Power indicator light fla

Operation 23Menu operationMenu systemPlease note that the OSD menus vary according to the signal type selected.*When a Video or S-Video signal is conn

Operation24Using the menusThe projector is equipped with on-screen display (OSD) menus for making various adjustments and settings.There are 10 differ

Operation 251. Picture menuSome picture adjustments are available only when certain input ports are in use. Unavailable adjustments are not shown on t

Table of contents iiiTable of contentsImportant safety instructions... 1Introduction ...

Operation26BrightnessAdjusts the brightness of the image. The higher the value, the brighter the image. And lower the setting, darker the image. Adjus

Operation 272. Pro-Picture menuSome picture adjustments are available only when certain input ports are in use. Unavailable adjustments are not shown

Operation283. Setting menu FUNCTION DESCRIPTIONMuteVolumeAdjusts the volume level.OSD TimeSets the length of time the OSD will remain active after you

Operation 294. Advance menuFUNCTION DESCRIPTIONMirrorThe projector can be installed on a ceiling or behind a screen, or with one or more mirrors. Cont

Operation305. Information menuThis menu shows you the current operating status of the projector.Some picture adjustments are available only when certa

Maintenance 31MaintenanceCare of the projectorYour projector needs little maintenance. The only thing you need to do on a regular basis is to keep the

Maintenance32Lamp informationWarning messageWhen the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, plea

Maintenance 33Step 1. Turn the power off and disconnect the projector from the wall socket.Step 2. Turn the projector over. Then loosen the screws and

Maintenance34Step 9. Resetting the lamp counter Do not reset if the lamp is not replaced as this could cause damage. i. Press and hold the Exit 5 butt

Maintenance 35Light Status & DescriptionPower Temp LampLamp events--(1) The projector needs 110 seconds to cool down. Or(2) Please contact your de

Table of contentsivProjector specifications ...38Timing chart ...

Maintenance36Service informationAccessories (included in the standard package) Optional accessories (not included in the standard package) Ordering p

Troubleshooting 37TroubleshootingTHE PROJECTOR DOES NOT TURN ON.NO PICTUREBLURRED IMAGEREMOTE CONTROL DOES NOT WORKCause RemedyThere is no power from

Specifications38SpecificationsProjector specifications All specifications are subject to change without notice. GeneralProduct name Digital ProjectorM

Specifications 39Timing chartSupported timing for PC inputSupported timing for Component-YPbPr inputSupported timing for Video and S-Video inputsResol

Specifications40DimensionsUnit: mm

Warranty 41WarrantyLimited WarrantyBenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof o

Regulation Statements42Regulation StatementsFCC statementCLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not in

Important safety instructions 1Important safety instructionsYour BenQ projector is designed and tested to meet the latest standards for safety of info

Important safety instructions2 Safety Instructions1. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 4

Important safety instructions 3 Safety Instructions (Continued)7. Do not place this projector in any of the following environments. - Space that

Important safety instructions4Safety Instructions (Continued)11. Do not step on the projector or place any objects upon it. Besides probable physical

Introduction 5IntroductionProjector featuresThe projector integrates high-performance optical engine projection and a user-friendly design to deliver